RCM Pro 取代了非常成功的 eRCM 往复式压缩机建模软件，该软件在帮助最终用户建模、调整、重新应用和配置他们的往复式压缩机方面已经有 20 年的历史。
面对如此多的压缩机、如此多的性能方法、如此多的 PLC 实现以及如此多的安全使用限制，ACI 的 eRCM 建模软件提供了对压缩机性能进行建模的理想解决方案。
只需通过直接输入或从 OEM 软件导入数据来指定压缩机的几何形状（框架、气缸、级、投掷、阀门等），eRCM Pro 就会显示该装置的性能曲线：压力与负载、压力与流量、压力vs. 压力等，包括净杆负载力图、PV/PT 卡、扭矩作用力等。
操作条件发生变化。在气缸的头端增加一个 500 in³ 的间隙槽是否会提供足够的卸载以适应新的操作图？您将在几秒钟内通过 eRCM Pro 获得答案。
厌倦了气体控制使用一种方法来预测装置性能，而工程师使用另一种方法，而 PLC/操作员正在使用另一种方法来实际控制硬件？eRCM 为您公司内的学科提供了一种方法论。
想看看打包机的卸货顺序能不能改进？使用 eRCM Pro，您可以轻松检查容积袋和末端停用的任意组合。包括添加垫片以增加固定间隙或向容积袋添加填充件以减少额外的间隙。您甚至可以在启动时检查安全性，并在某些阀门出现故障时检查安全性。
如果没有改进模型的能力，任何压缩机性能计划都是不完整的。eRCM Pro 就是这样做的。在调谐部分输入有效的分析仪数据，eRCM Pro 将自动调整性能预测以适应脉动、实际阀门和寄生损失、摩擦损失等的真实世界影响。
File size: 24 MB
RCM Pro replaces the highly successful eRCM Reciprocating Compressor Modeling Software, which enjoyed a twenty-year journey of helping end users model, tune, reapply, and configure their reciprocating compressors.
With so many compressors, so many performance methods, so many PLC implementations and so many restrictions for safe use, ACI’s eRCM Modeling Software provides the ideal solution to model compressor performance.
Simply specify the compressor’s geometry (frame, cylinder, stage, throw, valving, etc.) via direct inputs or by importing data from OEM software, and eRCM Pro displays that unit’s performance curves: Pressure vs. Load, Pressure vs. Flow, Pressure vs. Pressure and more, including graphs of net rod load forces, PV/PT cards, Torque Effort, and more.
Operating conditions change. Will adding a 500 in³ clearance pocket to a cylinder’s head end give enough unloading to accommodate the new operating map? Within seconds you’ll have your answer via eRCM Pro.
Tired of Gas Control using one method to predict unit performance, while engineers use another, and the PLC/operators are using yet another method to actually control the hardware? eRCM provides one methodology for disciplines within your company.
Want to see if the packager’s unloading sequence can be improved? With eRCM Pro you can easily check any combination of volume pockets and end deactivation. Including adding spacers to increase fixed clearances or adding filler pieces to volume pockets to decrease additional clearances. You can even check safety at Start Up, and check safety if certain valves fail.
No compressor performance program would be complete without the ability to improve your models. eRCM Pro does just this. Enter valid analyzer data in the tuning section, and eRCM Pro will auto-adapt the performance predictions to accommodate the real-world effects of pulsation, actual valve and parasitic losses, friction losses, etc.
Features:
Model entire stations
Manage previous versions of your models
Fully International aware interface
Impressive list of Units of Measure
Advanced thermodynamic calculations using ProSim now included – full support for 400 gases with liquid dropouts
Still, the fastest performance and graphs in the industry!
As you expect with eRCM, fully dynamic compressor performance, PV cards, Force Plots, Torque Effort Plots, etc.
Advanced support for Side Streams and Gas Mixing
Improved valve modeling
Improved gas preheat modeling
Improved Load Step Sequence creation
Full tables, curves, and 3D plot generation
Support for Clearance devices, End Deactivation devices, Timed-valve Closing devices, Gas Stepless devices, and even variable stroke devices
原创文章，作者：steven，如若转载，请注明出处：https://rr3d.cn/12283.html
